- 1 year warranty.
- Model: 500-03700, JL05BG
- Brand: CMS
- Length: 500mm
- Rated to 20amp
- J series (used in Jayco and Avida)
-
CMS products provide a DIY 240V wiring solution for your RV. This is a connecting cable that fits all J series CMS products. It comes in various lengths as shown in the title. Each cable has a female and male end so they cannot be connected incorrectly. Each connection has a security clip that can only be separated by manual manipulation, they will never come adrift within the wall provided they are pushed tight until the clip engages. The rating of the cables exceeds the 15amp supply provided to RV's. The number of cables and power points should be limited to either 10 double power points or 12 single power points per circuit, however your electrician may vary this depending of expected loads. For example an electric stove would reduce this number. In any event the circuit will be physically limited to 16amps by the 16amp circuit breaker. Cables should be longer than the distance between power points. As a general rule allow 300mm extra, but even more will not harm. Remember the cables clip in facing down from the power point within the wall, so branching off to a power point above will require curving the cable back up. Cables can be joined using a CMS double adapter. See dimensions of double adapters. Each cable end has a cross section of 25mm x 16mm. Image shown is of a 3000mm cable. The licensed electrician will cut the first cable to insert the 16amp double pole circuit breaker or 16amp RCD as well as connect the earth wire to the chassis. Cables should not be placed near any sharp edges which may damage the outer sheath. 240V outlets cannot be placed within certain distances of a shower or bath, your electrician can advise. Ensure cables are securely clipped together and inspected by your electrician before completing cladding. If running power below floor to the other side of the RV it must be enclosed within the chassis or conduit. Features -
The CMS Power Inlet, 15A – White (Male) is an essential component for a DIY 240V wiring solution in your RV. This 10amp power outlet, designed for CMS 240V cables, is typically the last outlet in a circuit as it doesn't offer a secondary connection. It features an automatic switch that cuts off current when an appliance is disconnected, ensuring safety and efficiency. The inlet requires 60mm of space from the mounting face to the rear wall and may extend into the cabin for thinner walls. Its dimensions are compatible with Jayco and Avida series, and it comes with a 1-year warranty. Features
- These can only be connected with related CMS cables.
- 1 year warranty.
- Model: 500-04312, JIL15WT
- Brand: CMS
- J series (used in Jayco and Avida)
-
The CMS Mounting Shroud – White offers a sleek, protective solution for your power installations. This shroud is designed for situations where power points exceed the wall recess, requiring a protective cover behind the wall. It's especially useful in areas like wardrobe interiors, where cables are exposed. The shroud ensures safety and neatness, covering the rear of both double and single CMS power points effectively. With dimensions of 137mm x 137mm and extending 30mm, it provides ample coverage without being obtrusive. Its white color seamlessly integrates with your interior design, maintaining a clean and professional look. This product comes with a 1-year warranty, ensuring quality and reliability. Features
- 1 year warranty.
- Model: 500-04284, J16CWT
- Brand: CMS
- Measures 137mm x 137mm, and extend 30mm.
-
Opt for the CMS Power Inlet, 15A – Black (Male) for a secure and efficient power source in your RV. This DIY 240V, 15amp power inlet is an essential part of the CMS wiring solution, fitting perfectly with CMS cables. It requires connection to a CMS circuit breaker before any outlets, ensuring maximum safety. The power inlet's sleek black design adds a modern touch to your setup. It needs 60mm of space from the outside mounting face to the rear, adaptable for various wall thicknesses. With a 1-year warranty and compatibility with Jayco and Avida series, this power inlet is a reliable and stylish choice for your electrical needs. Features
- These can only be connected with related CMS cables.
- 1 year warranty.
- Model: 500-04313, JIL15BK
- Brand: CMS
- J series (used in Jayco and Avida)
-
The CMS Power Outlet With Auto Switch, 10A – White (Female) is a sophisticated and safe solution for your RV's electrical needs. This DIY 240V, 10amp power outlet is designed to fit CMS cables, offering a reliable and specialized connection. The automatic switch feature cuts off current to ensure safety when appliances are disconnected. It requires 60mm of space from the mounting face to the rear wall, making it suitable for various wall thicknesses. The screw holes are strategically placed for easy installation. This outlet is part of the J series, used in Jayco and Avida, and includes a 1-year warranty for peace of mind. Features
- These can only be connected with related CMS cables.
- 1 year warranty.
- Model: 500-04310, JOL10WT
- Brand: CMS
- J series (used in Jayco and Avida)
-
The CMS Mounting Block, designed exclusively for beige CMS DIY 240v power points, is an essential accessory for your electrical installations. This power point mounting block is ideal for situations where power points cannot fully recess into the wall. It accommodates both double and single CMS power points, offering versatility for various electrical setups. The mounting block allows external cable connections, typically safeguarded within a conduit that aligns with the block's lower face. It features three accessible entry points at the bottom and one on each side, facilitating easy cable entry and secure attachment to the power point. The CMS Mounting Block is not only functional but also aesthetically pleasing, blending seamlessly with your interior decor. It comes with a 1-year warranty, ensuring reliability and customer satisfaction. Features
- 1 year warranty.
- Model: 500-04200, JMBBG
- Brand: CMS
- Dimensions (w)135mm x (h)105mm x (d)35mm
-
The CMS Mounting Block, designed exclusively for beige CMS DIY 240v power points, is an essential accessory for your electrical installations. This power point mounting block is ideal for situations where power points cannot fully recess into the wall. It accommodates both double and single CMS power points, offering versatility for various electrical setups. The mounting block allows external cable connections, typically safeguarded within a conduit that aligns with the block's lower face. It features three accessible entry points at the bottom and one on each side, facilitating easy cable entry and secure attachment to the power point. The CMS Mounting Block is not only functional but also aesthetically pleasing, blending seamlessly with your interior decor. It comes with a 1-year warranty, ensuring reliability and customer satisfaction. Features
- 1 year warranty.
- Model: 500-04200, JMBBG
- Brand: CMS
- Dimensions (w)135mm x (h)105mm x (d)35mm
-
Enhance your electrical setup with the CMS Single Power Point – Double Pole – White, a key component for Caravan or RV owners. This product is a double pole, single power point, designed for exclusive use with 240V CMS cables. Its sleek white finish complements any interior design. It extends 32mm into the wall, and for thinner walls, it can be paired with a mounting block or shroud for a seamless installation. This power point's compatibility with specific CMS cables ensures a safe and efficient electrical connection. Its dimensions are 130mm x 72mm, making it a compact and convenient choice for any space. Features
- These can only be connected with related CMS cables.
- 1 year warranty.
- Model: 500-03602, J16.1NW
- Brand: CMS
- Overall size is 130mm x 72mm
- J series (used in Jayco and Avida)
-
The Dometic PerfectView RVS 545 is a state-of-the-art colour reversing camera system, designed to enhance safety and convenience in caravans and RVs. Featuring a flat 5″ LCD monitor with super-bright LED backlighting and AHD technology, it offers outstanding image quality. The system supports up to three cameras and includes a small, discreetly housed color camera. It boasts features like a temperature-controlled heater, normal or mirrored picture function, and automatic recognition of a trailer camera. This system is a perfect blend of advanced technology and user-friendly design.
Specifications
-
- Model: RVS545 AHD-KIT
- Other Identifiers: , 9600000562
- Brand: Dometic
- Barcode: 9331391008179
M55L AHD Monitor
- Operating Voltage: 12V / 24V
- Resolution: 385,000 pixels
- Dimensions (mm): 148(w) x 87(h) x 26(d)
- Protection Class: IP40
- Vibration Resistance: 6.00 g
- Colour: Black
CAM45 Camera
- Operating Voltage: 11-16V
- Resolution: 250,000 pixels
- Dimensions (mm): 80(w) x 68(h) x 46(d)
- Diagonal Picture Angle: 120 degrees
- Horizontal Picture Angle: 80 degrees
- Vertical Picture Angle: 65 degrees
- Protection Class: IP69k
- Vibration Resistance: 6.00 g
- Colour: Silver
- Shipping Weight: 2.20 Kgs.
- Shipping Dimensions: 22 cm x 20 cm x 28 cm.
-
-
The Truma Cowl Grill for Hot Water System in Cream is an essential component for your Truma gas/electric hot water systems. As a genuine part, it guarantees compatibility and performance. Its cream color complements the aesthetic of your system, and its design ensures it functions effectively. The availability of the outer cover in the store offers a complete solution for your hot water system's exterior needs. RV Spares Online provides this cowl grill as a testament to their commitment to offering genuine, high-quality parts for your RV.
-
The Victron Orion-Tr Smart DC-DC Charger is a professional, adaptive 3-stage charger with built-in Bluetooth, designed for use in dual battery systems in vehicles or boats. It efficiently charges the service battery using the alternator and start battery, can be monitored and programmed via Bluetooth, and features a remote control option. This charger is suitable for both lead acid and lithium batteries, handling high temperatures and offering a full-rated output up to 40°C, making it a versatile and reliable choice for managing your charging needs. Victron Number: ORI121236140
-
Complete your RV roof restoration with Dicor's Acrylic Roof Coating Part 2, the final step in a two-part system designed to renew and protect your rubber roofing. This high-solids acrylic elastomer coating offers superior weatherability, UV resistance, and flexibility, ensuring your RV's roof remains in top condition. Suitable for EPDM rubber & PVC roofing, it requires prior application of Dicor’s Cleaner/Activator for best results. With easy application and exceptional protective qualities, Dicor's Acrylic Coating is essential for extending the life and enhancing the appearance of your RV roof. Two coats are required.
For use on:
EPDM rubber & PVC roofing: Dicor’s Part 1 Cleaner/Activator Primer (RP-CRP-Q) is required prior to coating.Preparation:
Thoroughly mix the contents for a minimum of 5 minutes prior to application. Use plastic sheeting to protect sidewalls and end caps of units. Be sure plastic runs to the ground/floor. EPDM and PVC roof surface must be cleaned/primed with Dicor’s Part 1 Cleaner/Activator (RP-CRP-Q) and free of residue or loose particles. Surface shall be completely dry and frost free before coating. Deteriorated or damaged substrates shall be repaired or replaced.Weather Precautions:
Dicor Acrylic Coating requires complete evaporation of water to cure. Cool temperatures and high humidity may slow down the curing process. Do not apply if weather conditions will not permit complete cure before rain, dew or freezing temperatures occur. Dicor Acrylic Coating will freeze and become unstable at temperatures below 32° F within a 48 hour period after application.Application:
Be sure the Part 1 Cleaner/Activator Priming process is complete prior to applying acrylic coating. Coating may be applied by medium nap roller or brush. Dicor Acrylic Coating shall be applied in a minimum of 2 coats at a rate of 1 gallon/125 sq. ft. per coat (i.e. 8’ X 30’ roof takes 4 gallons). Actual gallons required will depend on the type of surface, texture, method of application and weather conditions at the time of application. All surfaces must be uniformly coated and free from voids, pinholes, or blisters. Entire coating process MUST be completed in one day, including Part 1 Cleaner/Activator and two coats of Acrylic Coating, each dry to the touch before proceeding. Caution: Keep out of reach of children. -
Dicor Self-Leveling Lap Sealant creates a secure, secondary seal over and along the roof edges, vents, hatches, solar panel brackets and screw heads. Suitable EPDM, TPO and PVC membranes, it adheres to aluminum, mortar, wood, vinyl, galvanized metal, fiberglass and concrete.
- This sealant makes a very nice self levelled finish on roofs - not suitable for walls
- This sealant makes it possible to create a continuous seal yet remain flexible.
- May be painted over after outer skin has formed.
- Clean surface of all dirt, loose paint, rust, oil and grease.
- Allow surface to dry before applying sealant.
- Use standard caulking gun or pumping system to apply sealant.
- In cold weather, warm container at room temperature before use.
-
The Tufflex PVC Roofing is a non-fleece backed PVC material that is puncture resistant and tear resistant. Tufflex is flexible with all the advantages of EPDM. We will provide 2 tubs of glue adhesive with this purchase.
- Highly flexible for easy installation
- Tear & puncture resistant
- Remains flexible throughout its lifetime
- Not affected by ponding water
- Sun, weather & chemical resistant
- Easy to maintain
-
Introducing the Dicor Rubber Roof Cleaner Concentrate – the ultimate 3.78L refill bottle designed specifically for RV maintenance. Crafted for EPDM rubber roofing, TPO, vinyl, fiberglass, and other exterior surfaces, this roof cleaner effortlessly lifts dirt and grime while being gentle on your RV. Its special formula includes water-softening agents that tackle hard water spotting, ensuring a spotless and radiant finish. Dicor's Roof Cleaner is safe for routine use and comes recommended for a variety of vehicles, including boats and motorcycles, thanks to its professional strength and biodegradable composition. For optimum care, follow up with Dicor Roof-Gard Roof Protectant to extend the life and look of your RV's roofing. For best results, follow with Dicor Roof-Gard Roof Protectant. IMPORTANT: Some products sold for RV maintenance contain petroleum distillates and citric ingredients. These chemicals will damage your roof membrane and shorten its life. Whether you choose Dicor’s Rubber Roof Cleaner or another brand, be sure the products you use do not contain these harmful chemicals.
- Rinse roof to remove loose dirt.
- Spray directly onto dirty surface area.
- Using a sponge, medium bristle brush, wash mitt or cloth, scrub surface in a circular motion.
- Rinse off with water and allow to dry completely. Repeat if necessary.
- For best results, follow with Dicor Roof-Gard Rubber Roof Protectant.
-
Rejuvenate your RV's aesthetic and ensure it remains in prime condition with the Dicor Roof Renew Kit, expertly engineered for 30 ft. RV units. Our comprehensive package delivers everything required for a full restoration, with clear instructions for easy application. Kit Components Overview: Cleaner/Activator: Unlock the potential of your RV's EPDM roof with our Cleaner/Activator. Its specialized formula transforms the roofing surface, creating an optimal bonding site for the Acrylic Coating. Acrylic Coating: Experience the strength of our high solids acrylic elastomer blend, designed to adapt to your roof's substrate and conditions. Coating Ready Cover Tape: Fortify your RV's roof by seamlessly sealing cracks or tears with our durable, fleece-backed sealing tape. Inclusions: Four gallons of Dicor EPDM Roof Acrylic Coating Two quarts of Cleaner/Activator One 4”x50’ roll of Coating-Ready Cover Tape Metal pan, 9” paint roller, two roller covers Masking tape and detailed instructions SURFACE INSPECTION AND PREPARATION
- Remove heavy deposits of dirt, leaves, pine needles and other debris using a broom or air blower. Any rocks or other large objects should also be removed.
- Roof must be in good condition. Do not apply on pryable or brittle roofing. EPDM surface must be free of standing water, ice, snow, oils or grease at time of application.
- Inspect roof carefully for cracks in the surface. These will need to be repaired later (see Coating Ready Cover Tape).
- EPDM Cleaner/Activator is designed for use on rubber roofing surface only and may damage other exterior parts of RV. It is highly recommended that you secure plastic sheeting over entire sidewalls as well as front and rear end caps to protect them from possible damage. If EPDM Cleaner/Activator contacts any surface other than roof, it should be rinsed immediately.
- DANGER: May cause severe irritation of the eyes and skin, gastrointestinal irritation, nausea, vomiting and diarrhea. May burn muost skin. Prolonged or repeated breathing of vapor or spray mist may be harmful. Use a respirator for protection from vapor or spray mist. Wear chemical resistant gloves, splash proof goggles and rubber overshoes. Avoid eye and skin contact. Do not take internally. Wash thoroughly after handling and before eating or smoking. Keep container closed when not in use.
- EPDM Cleaner/Activator is a ready-to-use material. It can be applied using a Hudson-type agricultural sprayer. Safety glasses with side shields and latex gloves are recommended when transferring EPDM Cleaner/Activator from the shipping container to the sprayer. Spray a fine mist that leaves roof damp. Adjust spray for weather conditions if necessary. If EPDM Cleaner / Activator is running off roof, you have used too much. If using a Hudson sprayer, adjust the spray nozzle to achieve a uniform spray pattern with a 3 to 4 foot arc. Application rate is 125 sq. ft. per quart over new or existing surfaces. Do not apply below 40 degrees F (4 degrees C).
- Allow EPDM Cleaner/ Activator to stand a minimum of 15 minutes to wet out and react with the EPDM surface. For best results, rinse with clean water using a minimum 2,000 psi pressure washer. Begin the power rinse at the lowest point on the roof and work upwards, keeping the pressure washer tip within 12” of the EPDM surface. Once the highest point on the roof is reached, work down again with a final rinse to remove any excess dirt or debris from the roof. After cleaning, the roof should be “white” in color, which is an indication that the surface has been chemically altered. Allow surfaces to dry thoroughly prior to application of two coats of the Dicor Acrylic Coating
- Clean equipment with water and biodegradable detergent. Purge the water from the pump and hoses using Mineral Spirits prior to storing for any length of time.
- Roof must be cleaned with Cleaner/Activator prior to application of Coating Ready Cover Tape.
- Any areas that are torn or cracked may now be repaired using the Coating Ready Cover Tape.
- Peel off a few inches of the release liner and carefully position the Coating Ready Cover Tape before applying. Any attempt to reposition the tape after application will damage the material.
- Apply pressure starting at the center of the tape and working towards the outside edges, removing any bubbles as you go. When finished, the edges should have no tunnels, openings or fishmouths.
- Only apply Coating Ready Cover Tape to areas that are to be coated the same day.
- Using the masking tape provided, mask off roof edging to enable coating to be applied with a clean, straight edge. Also, mask other surfaces where you do not want coating to be applied.
- Dicor White Acrylic Coating must be preceded with Dicor EPDM Cleaner/Activator to ensure proper adhesion (See Cleaner/Activator application). Cleaner/Activator must be removed by power washing prior to application of Acrylic Coating.
- All surfaces must be clean and free of residue or loose particles, degraded substrate, grease, oil, dirt, or other contaminates. Surfaces shall be completely dry and frost-free before coating.
- Dicor Acrylic Coating shall be applied in a minimum of a 2 coats at a rate of 1 gallon per 125 sq. ft. per coat (i.e., 8’X30’ roof takes 4 gallons). Actual gallons required will depend on the type of surface and texture, method of application, and weather conditions at the time of application. All surfaces must be uniformly coated and free from voids, pinholes, or blisters.
- Thoroughly mix the contents for a minimum of 5 minutes prior to application. Dicor Acrylic Coating may be applied by roller (provided) or brush. Dicor Acrylic Coating shall be applied in a minimum of 2 coats at a rate of 1 gallon per 125 sq. ft. per coat (i.e., 8’X30’ roof takes 4 gallons).
- Allow to dry for 12 to 24 hours depending on weather conditions.
-
Protect your RV's rooftop from the relentless sun with Dicor Roof Gard UV Protectant. This 3.78L refill bottle offers a safeguard against the damaging effects of UV rays, water, and dirt. Suitable for various roof types including rubber, vinyl, PVC, TPO, and fiberglass, its mild, non-abrasive formula ensures cleanliness and prolongs surface life without leaving any residue. With a protective finish that repels dust and water, and a composition free from silicone, oils, waxes, glycerin, or petroleum distillates, it's gentle yet effective. Perfect for an array of outdoor gear and vehicles, this product also protects countertops, furniture, and automotive detailing. Follow Rudy’s advice and opt for Roof-Gard to ensure your RV’s roof membrane remains in peak condition without harmful chemical damage.
A Tip From Rudy: Some products sold for RV maintenance contain petroleum distillates and citric ingredients. These chemicals will damage your roof membrane and shorten its life. Whether you choose Dicor’s Roof-Gard or another brand, be sure the products you use do not contain these harmful chemicals.
Directions:
- Clean roof first with Dicor Roof Cleaner.
- Spray directly on to clean surface, out of direct sunlght in 3′ X 3′ sections. One quart treats up to a 40′ RV.
- To provide for even coverage, wipe with soft cloth or sponge mop.
- For MAXIMUM UV PROTECTION reapply every 3-5 weeks or after every cleaning.
-
Keep your RV's roof in immaculate condition with Dicor Rubber Roof Cleaner Concentrate. This 478ml bottle is specially formulated to clean RV EPDM rubber roofs, TPO, vinyl, and fiberglass without harshness. Battle against hard water spots with the cleaner's built-in softening agents and maintain a gleaming surface effortlessly. This cleaner is safe for regular maintenance of all RV roofing and exteriors, and is also suitable for use on boats, personal watercraft, and even automobiles. With its ready-to-use, professional-strength formula, the Dicor Rubber Roof Cleaner is an essential part of your vehicle care routine. For the best results, follow with Dicor Roof-Gard Roof Protectant to give your RV that extra layer of longevity and shine. For best results, follow with Dicor Roof-Gard Roof Protectant. IMPORTANT: Some products sold for RV maintenance contain petroleum distillates and citric ingredients. These chemicals will damage your roof membrane and shorten its life. Whether you choose Dicor’s Rubber Roof Cleaner or another brand, be sure the products you use do not contain these harmful chemicals.
- Rinse roof to remove loose dirt.
- Spray directly onto dirty surface area.
- Using a sponge, medium bristle brush, wash mitt or cloth, scrub surface in a circular motion.
- Rinse off with water and allow to dry completely. Repeat if necessary.
- For best results, follow with Dicor Roof-Gard Rubber Roof Protectant.
-
Shield your RV's roof from the rigors of nature with Roof-Gard RV Roof Protectant, your go-to solution for RV paint protection. This premium protectant offers your vehicle defense against fading, oxidization, drying, and cracking caused by harsh UV rays, water, and dirt. Suited for a range of materials including rubber, vinyl, PVC, TPO, and fiberglass, its gentle, non-abrasive formula ensures your surfaces stay cleaner longer without leaving behind any oily residue. Enjoy the added benefits of a dust and water-repelling finish that simplifies maintenance and a formula free from harmful silicones, oils, waxes, glycerin, and petroleum distillates. Ideal not only for RVs but also for boats, watercraft, and various outdoor items, Roof-Gard secures the longevity and pristine condition of your investments. Apply it to enhance and protect countertops, spa covers, and various types of furniture.
A Tip From Rudy:
Some products sold for RV maintenance contain petroleum distillates and citric ingredients. These chemicals will damage your roof membrane and shorten its life. Whether you choose Dicor’s Roof-Gard or another brand, be sure the products you use do not contain these harmful chemicals.
Directions
- Clean roof first with Dicor Roof Cleaner.
- Spray directly on to clean surface, out of direct sunlght in 3′ X 3′ sections. One quart treats up to a 40′ RV.
- To provide for even coverage, wipe with soft cloth or sponge mop.
- For MAXIMUM UV PROTECTION reapply every 3-5 weeks or after every cleaning.
-
The Dometic Cara D door is a white sandwich door panel for RVs with an aluminium frame and integrated a high security safety mesh screen, including blind and four point locking system. Cut out size required: 1850mm (height), 620mm (width). This item will ship on a pallet so a business address is preferable. Please contact us with any questions! Features:
- Highly durable glass
- Highly resistant safety mesh
- Four-point locking system
- Easy to operate chrome door lever
- Integrated blind that blocks incoming light
